DIY Tutorial: How to Add Grommets to Curtains

grommots

Now that we are using our family room regularly, window treatments were on the priority list for a few reasons:

1. Did I mention we have 9 windows in this room?
2. Daytime television watching is impossible due to glare
3. With constant sunlight streaming in, the fabric on our couch fading is a concern long term

After hunting around for a while, a regrettable impulse buy at IKEA that left us $60 in the hole, and even searching Joann Fabrics with plans to make our own, we ended up choosing with these punchy geometric Farrah Fretwork drapes in blue from Target.

(The happy ending is that the regrettable curtains are now hanging in our bedroom and look much better there.)

grommots3

I like the clean look of curtains with grommets, and also think they are easier to open and close. Of course, it’s much harder to find curtains with grommets, so I decided to add them myself! It was EASY.

I purchased 4 packs of Dritz Brushed Silver Grommets from Amazon. They are silver colored plastic, very easy to install and look great!

 How to Add Grommets to Curtains

1. First I hemmed the curtains 6 inches shorter. I did this, first, because the grommet instruction requires a 4 inch header. Second, I needed to make them shorter because we didn’t want the curtains touching the baseboard heating system – fire hazard! They look a little silly right now, but one side is hidden by the couch, and the other will be behind our future entertainment console.

2. Next, I measured the width of my curtain. Don’t trust the measurement on the package if you are using store-bought curtains! It’s not always accurate  My curtain was roughly 62″ wide. To know how to space your grommets, divide this number by 16 (because you are adding 8 grommets), which, for me, comes out to 3.9″. (Doubled to 7.8″ between grommets.)

grommets

grommots83. I spent $10 on a measuring square and it made this task very easy. (Even for a typical just-wing-it-and-guess girl like myself.)  Using the tracing circle guide that came with the grommets, I marked out in pencil where the center of each circle should be – 2″ from the top of the curtain, and 3.8″ away from the center of the circle on either side of it. This sounds complicated (and was intimidating at the first go), but worked quite well. ALWAYS measure twice (or three times!) before you cut.

grommots7

4. Next, cut out the circles. I started by snipping into the middle of the circle, and then cutting around the outline.

5. Next, open the grommets. Each grommet comes in two pieces – one has teeth and one does not.

grommots5grommots66. Place the one with teeth on the ground, teeth facing up. Next, place the fabric over the grommet, with center the hole you just cut out with the grommet.

7. Next, place the toothless grommet over the top. You are sandwiching a bit of the fabric between the two pieces. To get the grommets to click together, firmly press down with the palm of your hand until it clicks into place.

grommots48. Repeat – again and again and again! I was able to do all four panels in an afternoon.

 

This is not a curtain installation tutorial. There are about 9,405,937,058 of those on the internet, and they will all tell you to “hang them high and wide” to make your window appear bigger. Unlike most people, we did NOT need to make our windows feel any bigger. We just left a little space between the finial and the wall and tried to replicate it on each side.  We chose chunky Allen & Roth curtain hardware from Lowes.

grommots2 And I’ve officially started dreaming up our TV console we plan to build. This is a Photoshopped version of what I’m thinking of. (You can see our current tiny one we are currently using here).

Have you added grommets to curtains before? Where do you like to shop for curtains? They are tough to find!

Save

Save

Related Post

2 comments

Leave a Reply

Your email address will not be published. Required fields are marked *